How To Remove Breech Plug Without Tool

Have you ever been in the middle of a game and your gun jams? Chances are, it’s because the breech plug is dirty. The breech plug is located at the back of the barrel, and it’s what seals the chamber from the rest of the gun.

Over time, powder and debris can build up on the breech plug, causing it to become stuck. If this happens, don’t panic! There are a few ways to remove the breech plug without a tool.

  • Unscrew the cap from the end of the gun
  • Unscrew the set screw that holds the breech plug in place
  • Pull the breech plug out of the gun
  • Clean the breech plug and set screw with a cloth
  • Screw the set screw back into the breech plug
  • Screw the breech plug back into the gun
  • Screw the cap back onto the gun

Traditions Firearms Video Series – Removing a Stuck Breech Plug

What do you soak a breech plug in?

A breech plug is a small, threaded cylindrical part of a firearm that seals the rear end of the barrel. Most breech plugs are made of brass. There are a few different ways to soak a breech plug.

One way is to soak it in hot soapy water. This will loosen any dirt or debris that may be on the plug. Another way is to soak the plug in denatured alcohol.

This will remove any oil or grease that may be on the plug. Once the plug is soaked, it is important to dry it off completely before reinstalling it into the firearm. This will prevent any moisture from getting into the barrel and causing rust or corrosion.

What is a breech plug?

A breech plug is a small, usually cylindrical part of a firearm that is inserted into the rear end of the barrel to close it. The breech plug is usually made of metal, but can also be made of other materials such as plastic or wood. Breech plugs are found in a variety of firearms, including muskets, rifles, pistols, and shotguns.

In muskets and rifles, the breech plug is usually located at the end of the barrel, just behind the muzzle. In pistols, the breech plug is located in the frame, just behind the cylinder. In shotguns, the breech plug is located in the receiver, just behind the barrel.

Breech plugs typically have a small hole in the center that allows for the passage of a small amount of powder or other propellant. When the firearm is fired, the pressure of the expanding gases from the burning powder pushes against the breech plug, sealing it in place. Breech plugs can be removed from a firearm for cleaning or repair.

In some cases, the breech plug may be replaced with a different type of plug that is better suited for the particular firearm. For example, a matchlock musket may be fitted with a flintlock breech plug, or a percussion cap breech plug may be used in a percussion cap firearm.

What size is the breech plug on a Thompson?

The breech plug on a Thompson is 3/4″ in diameter.

how to remove breech plug without tool


Removing rusted breech plug

If your breech plug is starting to show signs of rust, it’s important to remove it as soon as possible. Rust can cause serious damage to your firearm and make it unsafe to use. There are a few different ways to remove a rusted breech plug.

You can try using a rust dissolver, WD-40, or even vinegar. Whichever method you choose, make sure you follow the instructions carefully and take proper safety precautions. Once the rust is removed, it’s important to apply a rust preventative to the breech plug and your firearm.

This will help keep rust from coming back and will keep your firearm in good condition for years to come.

Muzzleloader breech plug removal tool

Are you having difficulty removing your muzzleloader’s breech plug? There are a few different ways that you can go about it, but the best way is to use a muzzleloader breech plug removal tool. There are a few different types of breech plug removal tools on the market, but they all essentially work in the same way.

The tool will have a handle and a rod with a small hook or notch on the end. You’ll insert the rod into the muzzle of your gun and hook it onto the breech plug. Then, you’ll use the handle to twist the rod and remove the breech plug.

Breech plug removal tools are relatively inexpensive and can be found at most sporting goods stores. They’re a must-have for any muzzleloader owner and can save you a lot of frustration down the road.

Cva breech plug removal tool

If you have a muzzleloader, then at some point you’re going to need to remove the breech plug. The best way to do this is with a specialized tool, like the CVA Breech Plug Removal Tool. This tool is specifically designed to remove the breech plug from your muzzleloader, and it’s easy to use.

Simply insert the tool into the breech plug and turn it counter-clockwise. The tool will do the rest, and you’ll be able to remove the breech plug with ease.


If you find yourself in a situation where you need to remove a breech plug without a tool, there are a few things you can do. First, try using a piece of string or a shoelace. Tie one end around the breech plug and the other end to a large object like a tree or a rock.

Then, pull on the string or shoelace until the breech plug comes out. If that doesn’t work, you can try using a wire hanger. Straighten out the hanger and create a small hook on one end.

Then, insert the hook into the hole in the breech plug and twist it until the breech plug comes out. If you’re still having trouble, you can try using a small piece of wood. Insert the wood into the hole in the breech plug and twist it until the breech plug comes out.

With a little bit of patience and some creativity, you should be able to remove a breech plug without a tool.

1 Comment

  1. […] barrel is held in place by two screws, one at the front and one at the back. These are called the breech plug screws. Remove these screws and the barrel will come off. And that’s it! You have now […]

Leave a Reply

Your email address will not be published. Required fields are marked *