How To Adjust Remington 710 Trigger

There are a few ways to adjust the trigger on a Remington 710, but the most common way is to use a trigger adjustment tool. First, you will need to remove the stock from the gun. Next, you will need to locate the trigger adjustment tool, which is usually located in the butt of the stock.

Once you have found the tool, you will need to unscrew the cap that is covering the adjustment screw. After the cap is removed, you will need to turn the adjustment screw clockwise or counterclockwise, depending on which way you want the trigger to move. Finally, you will need to replace the stock and test the trigger.

  • Remove the stock from the gun
  • Unscrew the trigger guard screws and remove the trigger guard
  • Unscrew the trigger adjustment screw and remove it
  • Insert a small screwdriver into the trigger slot and turn it clockwise to tighten the trigger, or counterclockwise to loosen it
  • Reassemble the trigger guard and stock

Remington 710 bolt disassembly, cleaning and reassembly.

Can I adjust the trigger pull?

Most guns can have their trigger pull adjusted. This is done by a gunsmith, and usually involves changing the size or shape of the trigger itself. For example, a trigger with a bigger surface area will have a lighter pull, while a smaller trigger will have a heavier pull.

What is the difference between Remington 700 and 710?

The Remington 700 is a bolt-action rifle that was first introduced in 1962. It is a popular rifle among hunters and shooters due to its accuracy and reliability. The 700 is available in a variety of calibers and has been used by the military and law enforcement.

The Remington 710 is a semi-automatic rifle that was first introduced in 1997. It is similar to the 700 in terms of accuracy and reliability, but it does not have the same bolt-action design. The 710 is available in fewer calibers than the 700 and is not as popular among shooters.

What Remington rifles are being recalled?

Remington Arms Company, LLC (“Remington”) is voluntarily recalling certain Model 887™ shotguns. The recall is being conducted to repair a defect that could cause the shotgun to discharge unexpectedly. Remington has received three reports of the shotgun firing unexpectedly.

There have been no reports of injury. This recall involves Model 887™ shotguns with serial numbers ranging from M3779001 to M4099999. The serial number is located on the bottom of the receiver.

The Model 887™ shotgun is a 12-gauge, pump-action shotgun with a 28-inch barrel. The shotgun has a black synthetic stock and forearm and is sold with a modified choke tube. “Remington” is printed on the left side of the receiver.

“Model 887” is printed on the right side of the receiver. Remington is advising consumers to immediately stop using the recalled shotgun and to contact a Remington authorized service center to schedule a free repair. Remington is contacting all known purchasers of the recalled shotgun directly.

This recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission.

Is timney elite hunter adjustable?

If you’re a hunter, you know that having a good trigger is important. The Timney Elite Hunter is an adjustable trigger that is designed for hunting rifles. It is a single-stage trigger that is adjustable for both pull weight and overtravel.

The Timney Elite Hunter is a great choice for those who want a high-quality, adjustable trigger for their hunting rifle. It is easy to install and adjust, and it provides a crisp, clean trigger pull that will help you make more accurate shots.

how to adjust remington 710 trigger


Remington 710 trigger assembly

The Remington 710 is a bolt-action rifle that was manufactured by Remington Arms from 1962 to 1983. It was designed as an inexpensive yet accurate hunting rifle, and was popular with budget-minded hunters. The 710 used a unique trigger assembly that was different from other Remington rifles of the time.

The trigger assembly on the 710 consisted of a trigger, sear, and hammer. The trigger was made of plastic and was connected to the sear by a pin. The sear was located in the trigger housing, and the hammer was located in the receiver.

The 710 used a two-stage trigger, which meant that the trigger had to be pulled all the way back in order to fire the rifle. The 710 was designed to be a budget-friendly hunting rifle, and it was popular with hunters who didn’t want to spend a lot of money on a rifle. The 710 was accurate and reliable, and it was a good choice for hunters who wanted a quality rifle without spending a lot of money.

Remington 700 trigger adjustment diagram

Remington 700 Trigger Adjustment Diagram The Remington 700 is a popular rifle, and one of the things that makes it so popular is its adjustable trigger. The trigger can be adjusted to your liking, and in this post we’ll show you how to do it with a Remington 700 trigger adjustment diagram.

There are two screws that control the trigger pull on the Remington 700. The front screw, labeled “FRONT,” adjusts the sear engagement. This is the amount of pressure required to release the sear and fire the rifle.

The rear screw, labeled “REAR,” adjusts the trigger pull weight. To adjust the trigger, start by removing the stock. With the stock removed, you’ll be able to see the trigger assembly.

Locate the two screws that control the trigger pull. Using a screwdriver, turn the “FRONT” screw to the left to decrease the sear engagement, or to the right to increase it. To adjust the trigger pull weight, turn the “REAR” screw to the left to decrease the weight, or to the right to increase it.

Once you’ve made your adjustments, replace the stock and test the trigger. If it feels good, you’re done! If not, make further adjustments as needed until you’re satisfied.

That’s all there is to it!

Remington 722 trigger adjustment

If you have a Remington 722 rifle, you may find that the trigger needs adjusting from time to time. This is a relatively simple process, but one that should be done carefully. To adjust the trigger, you will need a small screwdriver.

First, locate the screw that is located just behind the trigger. This is the screw that controls the trigger pull. Turn the screw clockwise to increase the trigger pull, or counter-clockwise to decrease the trigger pull.

Be sure to test the trigger after each adjustment to see how it feels. It’s important not to adjust the trigger too much, as this can affect the accuracy of the rifle. If you’re not sure how much to adjust the trigger, it’s always best to err on the side of caution and make small adjustments.

With a little bit of time and patience, you should be able to find the perfect trigger pull for your Remington 722 rifle.


If you own a Remington 710 and are looking to adjust the trigger, there are a few things you need to know. First, the trigger adjustment screw is located in the front of the trigger guard. Second, you’ll need a small allen wrench to adjust the trigger.

And finally, be sure to read the owner’s manual before making any adjustments. With those three things in mind, adjusting the trigger on your Remington 710 is a relatively simple process. First, loosen the set screw in the front of the trigger guard with the allen wrench.

Next, turn the adjustment screw clockwise to increase the trigger pull weight, or counterclockwise to decrease it. Once you’ve found the desired trigger pull weight, tighten the set screw and you’re all done.

Leave a Reply

Your email address will not be published. Required fields are marked *